Lens and sensor care
Clean a lens gently and in order: blow dust off with air first, then use a soft brush, and touch the glass with a cloth only if needed. A little dust on the front element rarely shows in photos, while aggressive cleaning can do harm. Let cold gear warm up in a sealed bag, and store it dry and ventilated.

In short
- Remove dust with air first, then a soft brush, and only then touch the glass with a cloth.
- A little dust on the front element rarely shows in photos; aggressive cleaning does more harm.
- Let cold gear warm up inside a sealed bag to avoid condensation.
- Store gear dry, ventilated and used: fungus thrives in warm, damp, dark places.
Why gentle cleaning matters
Lens glass carries thin coatings that reduce flare and reflections. Grit rubbed across them with a cloth can leave fine scratches.
A few specks of dust on the front element rarely show in photos, especially at wide apertures. Fingerprints and smears matter more, because they lower contrast and cause haze.
So the rule is: clean when needed, in the right order, with the least force.
Cleaning a lens: blower, brush, cloth
First use a hand blower to puff away loose dust. Avoid blowing with your mouth, which adds moisture and droplets. Canned air can spray propellant, so many photographers avoid it.
Then use a soft, clean lens brush for stubborn particles, brushing outward from the centre.
For smudges, use a clean microfibre cloth, or lens tissue with a drop of lens cleaning fluid applied to the tissue, not the glass. Work in gentle spirals from the centre outward. Never use household glass cleaner or clothing.
Clean the rear element even more carefully, since marks there show more. Keep both caps on when the lens is not in use.
Cleaning the sensor
Dust on the sensor shows as soft dark spots, most visible in sky at small apertures such as f/16. Photograph a plain bright surface at f/16 to check.
Start with the camera's built-in cleaning function, then a hand blower with the camera facing down so dust falls out. Never use a brush or blower that touches the sensor surface, and never compressed air.
For stuck spots, wet cleaning swabs and fluid made for sensors are available, but a mistake can be costly. If you are unsure, a professional service is the safer choice. Follow the camera maker's instructions.
Changing lenses and condensation
Change lenses quickly, with the camera facing down and out of the wind. Keep spare lenses capped at both ends.
Moving cold gear into a warm, humid room makes water condense on and inside it. Before going indoors, seal the camera in a plastic bag and let it reach room temperature, which may take an hour or more (approximate).
If condensation forms, do not shoot or change lenses. Remove the battery and card and let the gear dry slowly; avoid heaters and hair dryers.
Storage, humidity and fungus
Lens fungus grows from spores that thrive in warm, damp, dark and still air. It forms web-like threads on or between elements and can etch coatings permanently.
Many sources suggest keeping relative humidity roughly between 40 and 50 percent for storage (approximate). Too dry for long periods may affect lubricants and seals; too damp invites fungus.
Practical options: a dry cabinet, or an airtight box with silica gel and a cheap hygrometer. Recharge or replace the gel when it is saturated.
Do not store gear in a closed bag after a wet day. Use lenses regularly, since light and moving air discourage fungus.
Everyday habits
Fit a lens hood: it blocks stray light and also shields the front element from fingers and rain.
Wipe off rain, sea spray and sand promptly; salt in particular can damage coatings and metal parts.
Clean the outside of lenses and cameras with a soft, slightly damp cloth, and keep rubber seals free of grit.
Frequently asked questions
Can I clean a lens with my T-shirt?
Better not. Clothing may hold grit and fibres that scratch coatings; use a blower first, then a microfibre cloth.
Does dust on the lens ruin photos?
Usually not. A few specks on the front element rarely show; fingerprints and smears are more harmful.
How do I check for sensor dust?
Photograph a plain bright surface or sky at f/16 and view the image enlarged; dust appears as soft dark spots.
Can lens fungus be removed?
Early fungus can sometimes be cleaned by a repair service, but it may leave marks on coatings. Prevention with dry, ventilated storage is much easier.