Home › Techniques

Long exposure photography

8 min read · Updated
Long exposure photography
Image: Jason, CC BY 2.0 · Wikimedia Commons

In short

  • A long exposure lets moving things blur while still things stay sharp, so a steady tripod is essential.
  • ND filters cut light in stops; each stop doubles the shutter time you need.
  • Bulb mode and a remote release let you go beyond the camera's longest timed setting (often 30 s).
  • Starting points are approximate: about 1/2–2 s for flowing water, 10–30 s for light trails, minutes for clouds.

What a long exposure does

A long exposure keeps the shutter open long enough for movement to turn into smooth blur while still parts of the scene stay sharp. Waterfalls become silky, waves turn to mist, car lights draw lines and clouds stretch across the sky. You need a steady support, usually an ND filter in daylight, and a little arithmetic in stops.

There is no fixed threshold, but photographers usually call anything from about half a second upward a long exposure (approximate). The look depends on how fast the subject moves compared with the shutter time.

The contrast between moving and still elements is what makes the picture: sharp rocks against soft water, a solid bridge above streaming traffic.

Gear you need

A sturdy tripod is the foundation. Any movement of the camera during the exposure blurs everything, not just the moving parts, so set the legs on firm ground and keep the centre column down.

A remote release, cable or app, or the 2-second self-timer, avoids shaking the camera as you press the button. For exposures longer than the camera's longest timed setting, use bulb mode: the shutter stays open while the button is held or the remote is locked.

In daylight you will almost always need a neutral density (ND) filter to slow the shutter enough. Cover the viewfinder eyepiece on cameras with an optical viewfinder, because stray light entering there can fog long exposures.

ND filters and counting stops

An ND filter darkens the whole image evenly. Its strength is given in stops: a 3-stop filter needs 8 times the shutter time, a 6-stop filter 64 times and a 10-stop filter about 1000 times.

To work out the new time, meter without the filter, then double the shutter time once for every stop the filter removes. For example, 1/60 s with a 10-stop filter becomes roughly 16 s (1/60 × 1024 ≈ 17 s, approximate). Many apps and printed tables do this for you.

You can also trade stops elsewhere: closing the aperture from f/8 to f/16 adds two stops, and lowering ISO from 400 to 100 adds two more. Avoid the smallest apertures if you can, because diffraction softens detail.

Very dark filters can add a colour cast, often warm or cool; shooting raw makes correction easy. Focus and compose before you screw the filter on, since autofocus may struggle through it.

Starting settings by subject

Flowing water: about 1/4 s to 2 s gives texture with smoothness; several seconds turns rivers and sea into mist (approximate).

Light trails from traffic: about 10–30 s at f/8–f/11 and ISO 100 after dusk, timed so several vehicles pass (approximate).

Moving clouds: one to several minutes, depending on wind speed, usually with a 10-stop filter in daylight (approximate). Crowds can be made to vanish with similar times, because people who keep walking leave no clear trace.

Always check the result and the histogram, then lengthen or shorten the time. Long exposures are a trial-and-error craft.

Noise, heat and batteries

Long exposures warm the sensor, which can add noise and bright 'hot' pixels. Many cameras offer long-exposure noise reduction: after the shot, the camera takes a second dark frame of the same length and subtracts it. It works well but doubles the waiting time.

Cold weather, below about 0 °C (32 °F), drains batteries faster, while warm nights raise noise. Carry spare batteries in an inner pocket.

With film, very long exposures need extra time beyond the simple calculation, because film loses sensitivity in dim light (reciprocity failure). Film data sheets give the correction; digital sensors do not have this effect.

Common mistakes

Wobbly support is the most frequent problem: a light tripod in wind, a bag swinging from the hook, or a bridge that vibrates with traffic all blur the frame.

Overexposing the highlights is the second: water and sky are bright, so check the histogram and use a slightly shorter time if they clip.

Finally, blur everything and nothing stands out. Include something solid, like rocks, a pier or buildings, to anchor the moving parts.

An exercise to try

Find a stream, fountain or busy road. Put the camera on a tripod and take the same frame at 1/250 s, 1/15 s, 1/2 s, 2 s and as long as the light allows. Compare how the motion changes and pick the time you like best for that subject.

Write down the times. After a few sessions you will know your favourite settings for water and traffic without guessing.

Frequently asked questions

How long is a long exposure?

There is no strict definition. Anything from about half a second to many minutes counts; what matters is that movement in the scene visibly blurs.

Do I need an ND filter?

At night, usually not. In daylight, yes for times longer than a fraction of a second, because even at f/16 and ISO 100 the scene is too bright.

What ND strength should I buy first?

A 6-stop filter suits water in soft light, and a 10-stop filter suits clouds and daytime minutes-long exposures. Many people start with one of these two.

Why is my long exposure blurry all over?

The camera moved. Use a firmer tripod, a remote or timer, keep the column down and protect the setup from wind and vibration.

Sources

Keep reading