Home › Editing

Editing exposure and contrast

7 min read · Updated

Start with the exposure slider to set overall brightness, then use highlights and shadows to recover detail at each end, and whites and blacks to set the brightest and darkest points. Add contrast last. Watch the histogram so you avoid clipping, and judge the result on a calibrated, not overly bright, screen.

Editing exposure and contrast
Image: Jkv, Public domain · Wikimedia Commons

In short

  • Set overall brightness first with exposure, then fine-tune the ends of the tonal range.
  • Highlights and shadows recover detail; whites and blacks set the end points.
  • The histogram shows clipping; a spike at either edge means lost detail there.
  • Raw files hold more recoverable highlight and shadow detail than JPEGs.

Order of work

Tonal edits work best in a fixed order: overall exposure, then the ends of the range, then contrast, and finally local tweaks. Doing contrast first often means you must undo it after changing exposure.

Most editing apps apply these sliders non-destructively, so you can return to any step. Still, a consistent order saves time and keeps results predictable.

The exposure slider

Exposure brightens or darkens the whole image, much like changing exposure in camera. In many raw editors one unit on the slider equals about one stop, which doubles or halves the brightness.

Set exposure by the main subject, such as a face or a key part of the landscape, rather than by the brightest sky. The other sliders handle the extremes.

Large exposure lifts reveal noise in the shadows, so a frame shot too dark by three or more stops (approximate) rarely looks clean after editing.

Highlights, shadows, whites and blacks

Highlights and shadows act mainly on the bright and dark parts of the image while leaving midtones mostly alone. Lowering highlights brings back cloud texture; raising shadows opens up dark areas.

Whites and blacks move the end points of the range. Pushing whites up until just before clipping and blacks down until just before clipping gives a full range from deep shadow to clean highlight.

Strong highlight and shadow moves together compress the range and can look flat or unnatural, with grey halos along edges. Moderate amounts usually look more convincing.

Contrast and the tone curve

Contrast spreads tones apart around the middle: brights get brighter and darks get darker. It adds punch but also deepens shadows and can clip ends you just recovered.

A tone curve gives finer control. A gentle S-shape adds contrast to the midtones, while lifting the bottom-left point creates a faded, matte look. Small curve moves have large effects, so adjust in small steps.

Many editors also have a midtone contrast slider that adds local edge contrast. A little adds crispness; a lot makes skin look rough and creates halos.

Reading the histogram while editing

The histogram plots how many pixels sit at each brightness, from black on the left to white on the right. As you move sliders, watch it shift.

A tall spike pressed against the right edge means highlights are clipped to pure white; against the left edge, shadows are clipped to black. Most editors offer a clipping warning that colours those areas.

A histogram is not a target shape. A night scene should sit to the left and a snow scene to the right. Use it to spot clipping, and use your eyes for mood.

Raw vs JPEG headroom

Raw files store more bits per channel than JPEGs, typically 12–14 versus 8 bits, so they hold more tonal steps. That headroom lets you recover a stop or two of highlights (approximate, depends on camera) and lift shadows with less banding.

A JPEG has already been processed in camera. Large adjustments can cause banding in skies and colour shifts, so shoot raw when the light is contrasty.

Frequently asked questions

Should I use exposure or brightness?

Use exposure for the overall level, since it acts like a camera stop. A brightness or midtone slider mainly moves middle tones and is useful for fine tuning afterwards.

Why does my photo look flat after recovering highlights and shadows?

Pulling both ends towards the middle reduces global contrast. Restore it by setting whites and blacks again or adding a gentle S-curve.

Is clipping always bad?

No. Small specular highlights, the sun or light sources can clip without harm. Avoid clipping in skin, clouds and other areas where you expect detail.

Why do my edits look too dark on other screens?

Your screen may be too bright. Lower its brightness to a moderate level or calibrate it, and check the histogram rather than trusting the display alone.

Sources

Keep reading